AudioControl EPIC4000

The AudioControl EPIC Series amplifier delivers massive, thrilling bass in a thermally efficient design. Combined with the separately available EPICENTER Bass Restoration Processor, it takes your bass experience to a whole new level. The EPIC4000 is the ultimate solution for competition audio. Designed for maximum efficiency and uncompromising stability down to the lowest impedances, this amplifier is equipped with oversized components and advanced thermal management to reliably deliver its rated power - not only in test mode, but also with demanding music tracks. It's not just about volume, it's about converting enormous power into pure low-frequency reproduction that dominates the soundstage and reaches legendary sound pressure levels (SPL).


Features:

✓ High performance competition class D :Experience high power and thermal efficiency that give even the most demanding subwoofer systems enormous power.

✓ High current design - 1Ω stable: Provides massive, stable output power required to drive even the most demanding low impedance speaker loads with 4000W RMS at 1 Ohm.

✓ Intelligent automatic reset protection circuitry: Multiple protection modes prevent damage should your amplifier malfunction.

✓ Variable Linkwitz-Riley low-pass and subsonic filter with 12 dB/octave: Optimize your audio setup by adjusting the frequency range of your subwoofer for earth-shaking bass response while protecting your subwoofers in vented enclosures.

✓ EPIC Boost Variable Frequency Bass Boost: Experience rich bass thanks to a bass equalizer with variable frequency (30 to 80 Hz) and a boost range of 0 dB to +12 dB.

✓ Solid Power/Speaker Connectors with Hex Bolts: Ensures maximum current flow and signal integrity for low impedance connections and consistent performance.

✓ EPICENTER link: Simplify installation with the EPICENTER LINK (included) to seamlessly connect the EPIC amplifier and EPICENTER Bass Restoration Processor (sold separately) for an unbeatable bass experience. 1 amp fuse protection keeps your devices safe.

✓ Remote control for ACR-E level control included: Customize your sound effortlessly with the included remote control knob for complete control.


Installation Requirements:

✓ Two power wires (0 AWG) and two ground wires (0 AWG) are required to operate this amplifier. This amplifier is designed for high currents!

✓ Each power cable (0 AWG) must be fused with a 200 amp fuse within 30 cm (12 inches) of the battery connection. This amplifier values reliable fuses - as well as rich bass.

✓ Only use high-quality 0 AWG OFC (oxygen-free copper) cable for all power and ground connections. This will give you a clean power supply and powerful bass! - Do NOT mount the amplifier on subwoofer cabinets. These two need their own space.

Technical data:

Amplifier Topology: Class D
Power Output RMS (14.4V, <1% THD):
1000 Watts @ 4 ohms
2000 Watts @ 2 ohms
4000 Watts @ 1 ohm
Frequency Response (+/- 1 dB): 10 Hz - 190 Hz
S/N Ratio: 104.8 dBa, Ref 1000 Watts @ 4 ohms
Power / Ground Wire Gauge: 0 AWG
Speaker Terminal Wire Gauge: 8 AWG
Recommended Fuse Rating: 200 Amp x 2 / 400 Amps x 1
Low Pass Filter: 12dB/octave Linkwitz-Riley, 40 Hz to 180 Hz
Subsonic Filter: 12 dB/octave Linkwitz-Riley, Off to 50 Hz
EPIC Boost: 30 to 80 Hz, Gain: 0 to 12 dB
Line-level Inputs: 0.5 to 12 VRMS
Chassis Dimensions (LxWxH): 533 mm × 155 mm × 52 mm


INCLUDED IN DELIVERY : EPIC4000 monoblock amplifier, wrench, screws, ACR-E remote control with cable, EPICENTER LINK
(1 meter cable), operating instructions.